Support > Hardware
KD3200, 3300, 3800, 4300, 4600
DIP Switch Settings and Functions
5.0 DIP Switch Settings and Functions 11.1 DT4100 Commands
11.2 HDG Command 11.3 Bit Pad Two Commands 11.4 MM Series Commands
11.2 HDG Command
Note:
The HDG Series command specifications differ from the Hitachi Seiko HDG series with respect to the following points:
- Resolution of 1/4096 is not possible. Instead resolution of 0.005 in.can be set.
- Use in the ID format is not possible
11.2.1 DIP Switch Setting Method
- (a)
- DIP Switch SW1
DIP Switch SW1 is used to set the resolution and coordinate reading mode
| Function | SW2 | ||||||||
|---|---|---|---|---|---|---|---|---|---|
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | ||
| Resolution | 0.025 mm | OFF | OFF | OFF | |||||
| 0.05 mm | OFF | OFF | ON | ||||||
| 0.1 mm | OFF | ON | OFF | ||||||
| 0.254 mm | OFF | ON | ON | ||||||
| 1000 lines/inch | ON | OFF | OFF | ||||||
| 400 lines/inch | ON | OFF | ON | ||||||
| 200 lines/inch | ON | ON | OFF | ||||||
| 100 lines/inch | ON | ON | ON | ||||||
| Remote mode | OFF | OFF | |||||||
| Switch stream mode | OFF | ON | |||||||
| Stream mode | ON | OFF | |||||||
| Point mode | ON | ON | |||||||
| Data transfer rate | 2 data/s | OFF | OFF | OFF | |||||
| 4 " | OFF | OFF | ON | ||||||
| 10 " | OFF | ON | OFF | ||||||
| 20 " | OFF | ON | ON | ||||||
| 45 " | ON | OFF | OFF | ||||||
| 55 " | ON | OFF | ON | ||||||
| ON | ON | OFF | |||||||
| ON | ON | ON | |||||||
- (b)
- DIP Switch SW2
DIP Switch SW2 is used to set the terminator and data transfer conditions.
| Function | SW2 | ||||||||
|---|---|---|---|---|---|---|---|---|---|
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | ||
| Terminator | CRLF | ON | |||||||
| CR | OFF | ||||||||
| Data length | 7 bits | ON | |||||||
| 8 bits | OFF | ||||||||
| Parity bit | NONE | OFF | *1 | ||||||
| ODD | ON | OFF | |||||||
| EVEN | ON | ON | |||||||
| Stop bit | 1 bit | ON | |||||||
| 2 bits | OFF | ||||||||
| Baud rate | 9600 bits/s | ON | ON | ON | |||||
| 4800 " | ON | OFF | ON | ||||||
| 2400 " | ON | OFF | OFF | ||||||
| 1200 " | OFF | ON | ON | ||||||
| 600 " | OFF | ON | OFF | ||||||
| 300 " | OFF | OFF | ON | ||||||
| 150 " | OFF | OFF | OFF | ||||||
- *1
- Can be set to either ON or OFF
- (c)
- DIP Switch SW3
DIP Switch SW3 is used to set the out-of-area data output and other-manufacturer command compatible functions
This switch is used to set command compatibility to digitizers of other manufacturers.
| Function | SW3 | ||||||||
|---|---|---|---|---|---|---|---|---|---|
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | ||
| Command mode | HDG series | OFF | OFF | OFF | OFF | ON | ON | ||
| Leading zero suppression | Enabled | ON | |||||||
| Disabled | OFF | ||||||||
| Beeper | Enabled | ON | |||||||
| Disabled | OFF | ||||||||
